Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Thornton?
Gate repair in Thornton typically costs $150 to $450 for common fixes like hinge replacement, latch alignment, and post tightening, while electric gate repairs involving motors, control boards, or sensors usually run $250 to $900. A full operator replacement sits higher, usually $700 to $1,900 including the unit. These are estimated ranges for the Thornton market in 2026; the written estimate we give you on site sets the final price.
Gates in Thornton take a hard combination of sun, freeze-thaw cycles, and Front Range hail, and that shows up in what fails first. We’re a gate specialist, not a general fence or garage-door company, so every job we take on is a gate job. That focus is why we can usually tell you a realistic price range before we arrive and confirm it once we’ve looked at the gate.
Quick Answer: What You’ll Pay
- Manual gate repair: $150 to $450 typical
- Electric gate repair (motor, board, sensor, wiring): $250 to $900 typical
- Operator replacement: $700 to $1,900 typical, including the new unit
- Same-day service: No premium. The price is set per job by the written estimate.
- Estimates: Free, whether the gate is manual or automated.
Gate Repair Cost Breakdown (2026)
Here’s how the line items usually break down across Thornton jobs. Ranges reflect what we see for residential driveways, HOA entrances, and small commercial gates in the north Denver metro.
| Repair | Typical Estimated Range | What It Covers |
|---|---|---|
| Hinge replacement | $150 to $350 | Removing worn hinges and setting new ones so the gate swings true |
| Latch and alignment fix | $150 to $300 | Realigning a sagging gate, adjusting the latch, tightening hardware |
| Post repair or resetting | $250 to $600 | Pulling a leaning post back to plumb, refilling the footing, resetting hardware |
| Control board replacement | $300 to $700 | The board itself plus labor and reprogramming of the operator |
| Operator motor replacement | $550 to $1,200 | New motor, labor, and testing on the existing gate |
| Safety sensor replacement | $250 to $500 | New photo-eye or loop sensor, wiring, and alignment |
| Wiring repair | $250 to $800 | Tracing a fault, replacing damaged low-voltage wire, testing the whole run |
| Full operator replacement | $700 to $1,900 | New operator, disconnect and disposal of the old one, reprogramming, access control check |
| New gate installation | $2,500 to $7,500+ | Gate, posts, operator, keypad or remote, and full commissioning |
What pushes a job toward the top of a range: a gate that’s been sagging for a while, wiring that’s been chewed by a weed trimmer or buried too shallow, and operators that were installed without a proper footing. What keeps it low: single-point failures on an operator we know well. We work on your brand, whether that’s LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule, and we diagnose and repair virtually any system without sending you elsewhere.
What Affects Gate Repair Pricing in Thornton
- The operator brand and vintage. Residential-grade operators like Ghost Controls and Mighty Mule are usually straightforward to diagnose and repair. Commercial, high-cycle systems from FAAC, BFT, and DoorKing take longer to test properly because there are more inputs to check, and that labor time shows up in the price. Brand familiarity matters: if we’ve worked on the same model dozens of times, the diagnostic goes faster and the estimate reflects it.
- Manual versus electric. A manual gate problem is usually mechanical: a hinge, a latch, a sagging post. Electric gates add a motor, a control board, sensors, and wiring, and any one of those can fail. Electric gate repair is core work for us, not an add-on, so we diagnose the whole system rather than just swapping a part and hoping.
- How long the problem has gone on. A gate that’s been dragging for one season is usually a smaller job than one that’s been dragging for three. Worn hinges wear the posts. A gate that off-tracks wears the operator. Fixing the cause early keeps the line items short.
- Front Range weather and soil. Thornton’s freeze-thaw cycles work on gate posts the same way they work on decks and fences: moisture gets into the footing, freezes, expands, and the post shifts. Hail takes its share of keypads and sensor lenses. Summer sun ages plastic housings and degrades exposed wiring. None of that is unusual here, and all of it affects the repair.
- Wiring condition. If the low-voltage run between the operator and the keypad or sensor is damaged, that’s additional labor. Burying a new run or fishing wire through conduit takes time, and we quote it honestly rather than lumping it into a guess.
- Safety and code upgrades. An older automated gate may need photo-eye sensors or a reversing feature that wasn’t required when it was installed. If your city requires a permit for a repair or replacement, ask your city’s building department before work starts, and we’ll build the permit need into the estimate.
Can You Repair My Gate the Same Day?
Often, yes. For the majority of Thornton calls, we diagnose and repair in one visit. That’s the benefit of gate-only focus: we arrive knowing what to check and with the right parts on the estimate, not on a hunch.
Same-day service doesn’t cost more. The price is set per job by the written estimate, full stop. Call (866) 389-4610. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If you reach us outside dispatch hours, we’ll book you into the next opening.
If you want the broader picture of what we handle, start at Gate Repair Thornton and we’ll point you to the right page.
Is It Cheaper to Repair or Replace My Gate?
Repair is almost always cheaper when the gate frame is sound and the failure is a single component. A $350 hinge or latch repair beats a $3,000+ new gate any day of the week.
Replacement starts to make sense when the frame is bent or rusted through, the posts can no longer be reset, or multiple systems fail in a single season. On the operator side, the line is clearer: a control board at $300 to $700 is usually cheaper than a whole new operator at $700 to $1,900, unless the motor is also aging out at the same time.
We’ll tell you straight which side of that line your gate is on after the on-site look. It’s the same answer we’d give a neighbor. For a deeper walk through what a repair visit involves, see our gate repair page.
How to Save on Gate Repair
The simplest saving is a free estimate. Call (866) 389-4610 and put a number on the problem before anything is unscrewed. A few other practical ways to keep the bill down:
- Fix it early. A dragging gate that gets fixed in month one is a hinge. In year three it’s a hinge plus a post plus possibly an operator part. Catching problems while they’re single-point saves real money.
- Keep the tracks and hinges clear. For a sliding gate, cleaning debris out of the track before it’s packed in prevents premature wear. On a swinging gate, keeping hinges from caking with dirt extends their life.
- Trim vegetation away from the operator and sensors. Low-voltage wiring and photo-eye lenses that get repeatedly whacked by lawn equipment are a common repair reason. A pass with the string trimmer at a respectful distance saves a service call.
- Tell us the brand and model when you call. If you know it’s a Linear or a Viking, say so. It shortcuts the diagnostic and can save you a trip.
- Bundle the little stuff. If you’ve noticed a tired latch alongside the electrical fault, mention both. Getting the small items tightened during the main repair is cheaper than booking a second visit.
- Ask for the estimate in writing. Ours is written, free, and clearly itemized, so you know exactly what each piece costs before you approve the work.
What Does Electric Gate Repair in Thornton Usually Cost?
Electric gate repair in Thornton typically runs $250 to $900. The wide range reflects the different failure points in an automated system:
- Motor failure: $550 to $1,200 for motor replacement on the existing gate.
- Control board failure: $300 to $700, including reprogramming.
- Safety sensor or photo-eye replacement: $250 to $500.
- Wiring fault: $250 to $800 depending on how much of the run needs replacing.
- Access control issue: keypad, remote, or receiver failure usually runs $200 to $500.
We cover the whole system, from the motor to the keypad. If the gate is acting up, we can usually tell over the phone whether it’s mechanical or electrical and set a realistic expectation before we arrive. If you manage an HOA or commercial property, we handle high-cycle operators too, including FAAC, BFT, and DoorKing.
Automated gates share a serious safety point with electrical panels: the operator is wired into line voltage and the gate itself can crush. A gate that won’t reverse properly on obstruction is a hazard. That’s not a job to tinker with at home. It’s why we test sensors, reversing features, and emergency stop functions as part of every electric repair.
FAQs – Gate Repair Cost
How much does a gate repair cost in Thornton?
Most gate repairs in Thornton run $150 to $450 for mechanical fixes and $250 to $900 for electric gate repairs. The written estimate we give you on site sets the exact figure. Call (866) 389-4610 for a free estimate.
Is gate repair cheaper than replacing the gate?
Usually, yes. A single repair at $150 to $450 against a new gate installation at $2,500 to $7,500+ is a wide gap. Replacement only wins when the frame or posts are beyond repair or multiple systems are failing. Call (866) 389-4610 and we’ll walk you through the call.
How much does an electric gate motor replacement cost in Thornton?
Motor replacement typically runs $550 to $1,200, and a full operator replacement with the unit, labor, and reprogramming sits at $700 to $1,900. The final number depends on brand and gate size. Call (866) 389-4610 for a free estimate.
Do you charge a diagnostic or service fee?
No. Estimates are free. We look at the gate, tell you what’s wrong, and give you a written estimate before any work starts. Call (866) 389-4610 to schedule one.
Can same-day gate repair cost more than a scheduled visit?
No. Same-day service carries no premium. The price is set per job by the written estimate. Call (866) 389-4610. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Get a Free Estimate on Your Thornton Gate
If your gate is dragging, the operator won’t arm, the keypad has gone silent, or the sensor is triggering at nothing, the fastest way to know what it costs is to have us look at it. Call (866) 389-4610 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 15 years of experience, and we work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. From diagnosis to final test, you have a single point of contact, and a single trade to deal with: gates. Back up and running is the goal, and we’ll tell you exactly what it will take to get there.
Pricing reflects the Thornton market as of 2026. Gate Repair Thornton offers free estimates – call (866) 389-4610.
Written by the team at Gate Repair Thornton.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Carrie Sutton"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Amit Shah"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Roger Sullivan